Page 1 of 1

Lenticular Prints

PostPosted: Mon Apr 30, 2012 8:58 pm
by drjez
I have been doing a bit of research and reading and am planning my first foray into making my own lenticular prints. Has anyone done any ? What is peoples experience of these and any pearls of wisdom or things to avoid.

Re: Lenticular Prints

PostPosted: Tue Jun 05, 2012 1:32 pm
by linuxluver
drjez wrote:I have been doing a bit of research and reading and am planning my first foray into making my own lenticular prints. Has anyone done any ? What is peoples experience of these and any pearls of wisdom or things to avoid.


No idea. But I'm also interested in how one might do this. I know a couple of 3D sites offer to sell lenticular prints of uploaded images.

Re: Lenticular Prints

PostPosted: Mon Jun 11, 2012 3:53 pm
by Vapymid
As I understand, to make a good lenticular print you need to have more than 2 offset images (the more, the better). After that the images need to be interlaced and printed and then laminated onto a blank lens.

Apparently, there exist blank frames in which you can just slide the print without laminating but I doubt they will work well.

It all sounds a bit too involved for my liking and no doubt expensive, but intriguing :-)

There are companies that supply software and materials, like this one (I've just done a quick search):
http://www.nexternal.com/vuethru/all-products-call.aspx

Regards

Re: Lenticular Prints

PostPosted: Tue Jun 12, 2012 3:54 pm
by 2eyedFroggy
hi guys,
here u can buy sheets and for small printing they point to a craftsman.
http://dplenticular.com/
Nice day.

Re: Lenticular Prints

PostPosted: Fri Nov 16, 2012 5:48 pm
by NeoMatrix
3D printing

Re: Lenticular Prints

PostPosted: Sun Aug 11, 2013 3:01 pm
by 51dfa2b7df7df38112000000
Hello everyone!

My name is Dory A. and I am from Romania.
Recently I start my own business here as a 3D event photographer
and lenticular printing services. If someone is interested to print his
3D photos can contact me at: adoru23@hotmail.com

Best

http://fotografie3d.wix.com/fotograf3d#!stereo-photography/cxq8

Re: Lenticular Prints

PostPosted: Thu Aug 29, 2013 3:23 am
by IC3D
51dfa2b7df7df38112000000 wrote:Hello everyone!

My name is Dory A. and I am from Romania.
Recently I start my own business here as a 3D event photographer
and lenticular printing services. If someone is interested to print his
3D photos can contact me at: adoru23@hotmail.com

Best

http://fotografie3d.wix.com/fotograf3d#!stereo-photography/cxq8


Hi Dory! Good luck on the new career. What kind of camera rig are you using? Just curious.

Re: Lenticular Prints

PostPosted: Fri Aug 30, 2013 8:58 pm
by skyemail
Lenticular printing is fun but can also be frustrating to get it done properly.
You can do it two ways:

Option #1
Use multiple images progressing from left to right. Figure 8 - 12 images depending on the quality you want to achieve.
There is some free software that allows you to print multiple images to align with lenticular lens sheets.
The software has a calibration check to use with your printer and make custom settings in the software.
After printing the interlaced images, you align the lens sheet with the photo, then carefully attach the lens on to your photo paper while peeling off the protective backing on the lens. To get out the air bubbles, use a squeegee, or run through a cold laminator while peeling off the backing. This takes some practice.

Option #2
There are a few software packages out there for that use left right pairs to create intermediate images for lenticular printing.
These are fairly expensive, depending on the quality. I have used Triaxes with varied results depending on the image pairs.

Links -
Lenticular sheets and free printing software for flip or 3D images: vuethru.com
Lenticular printing software for creating multiple images and printing: triaxes.com

Hope this helps...
Steve

Re: Lenticular Prints

PostPosted: Sat Nov 01, 2014 6:54 pm
by itsikw
We are printing stereo images in lenticular media for free 3D viewing: http://www.pop3dart.com/stereoprints.html
We will be happy to serve this community.

Re: Lenticular Prints

PostPosted: Mon Sep 14, 2015 5:03 pm
by RichyT
Vapymid wrote:Apparently, there exist blank frames in which you can just slide the print without laminating but I doubt they will work well.



I bought the frames but the software was a lot more. I could not get it working well on my own. The issue was partly that printer resolution did not match the spacing of the lenticules (?) and also that getting the alignment of the paper right was difficult. Some 3D effect was attainable but not satisfactory. I may give them another go when I get a new printer.